Anti Slip Waterbased Epoxy Floor Paint

SONY DSC

colours

 

 

 

 

 

1. DESCRIPTION

Antel Anti Slip Epoxy Floor Paint is a two pack pigmented floor paint with aggregate, recommended for use over high alumina concrete and other fresh concrete and alkaline surfaces such as chalk, marble and limestone chips. The product is ideal for use as a garage floor coating.

2. USES

Offices, factories, abattoirs, concrete floors etc.

3. PACKAGING

1 litre, 2.5 litre and 5 litre cans.

4. COLOUR

Light – mid – dark grey, tile red, white light – dark blue.
Specific colours can be supplied upon request, within reason.

5. USAGE RATE

Every litre of Water Based Epoxy Floor Paint will cover approximately 6-7 squared metres (based on a non porous, smooth surface), however this will vary depending on how thickly you apply the material and also how porous the surface is.

If you are unsure on the porosity of the surface, we recommend you buy a little more than you think you will need to ensure you don’t run out part way through the application.

6. SHELF LIFE

12 months in sealed container.

7. INSTRUCTIONS FOR USE

7.1 Preparation: Although Water Based Epoxy Floor Paint will over coat most other finishes and paints, the best results are achieved when surfaces are clean and free of other finishes/coatings. All surfaces should be damp dry or at least not subject to running water.

7.2 Mixing: The performance of the coating can be seriously impaired if the following instructions are not strictly adhered to.

The pot life is approximately 1.5 hours. This is based on a temperature of 20 degrees C/68 degrees Fahrenheit. If you are applying the coating in higher temperatures, the pot life may be reduced. The material will become unworkable once outside of this pot life.

Once mixed, it is only possible to apply a single coat. Do not attempt to return to the mix to apply a second coat.

For simplicity we would recommend getting a separate pack of Water based Epoxy Floor Paint for each coat. However, if you would like to buy just the one pack for both coats, you will need to accurately divide the resin and hardener packs equally and mix in a separate container for each of the coats. We suggest you divide the packs by volume in a measuring jug to ensure accuracy.

7.3 Application: WARNING – DO NOT APPLY IN TEMPERATURES BELOW 10 DEGREES C/50 DEGREES FAHRENHEIT AND ENSURE THERE IS AT LEAST A 4 HOUR WEATHER WINDOW.

PRODUCT CAN BE APPLIED IN MILDLY DAMP CONDITIONS BUT WILL NOT TOLERATE STANDING WATER.

1. Clean the surface you will be applying the Water Based Epoxy Floor Paint to. If there are any leaks, these should be repaired with Antel Waterstop, Antel Epoxy Putty or Antel SBR Bonding Agent before applying the Water Based Epoxy Floor Paint. If unsure, please contact us for technical advice.

2. Pour the contents of the smaller container into the larger container and mix thoroughly (ideally with a mixer paddle) for a minimum of three minutes, so that the two components are completely mixed.

3. Apply the first coat by brush, roller or spray. If the temperature is above 20 degrees C/68 degrees Fahrenheit, wait 6 hours before applying the second coat. If the temperature is below this, wait a full 24 hours before applying the next coat.

4. Apply the second coat.

7.4 Curing: Tack Free full Cure
at 20°C 65% RH 8 hours 3 days
at 8°C, 65% RH 24 hours 7 days
Pot life at 20°C 1.5 hours
Pot life at 10°C 2.5 hours

7.5 Cleaning Tools: Clean tools immediately after use with clean water

8. TYPICAL PERFORMANCE PROPERTIES

Taber abrasion Index (Mg) 20 per 1000 cycles.
Chemical Resistance:
Resistant to most dilute alkali systems e.g. 10% Sodium Hydroxide but has limited resistance to acidic attack e.g. Hydrochloric Acid.
Resistance to vehicular traffic – Good. Resistance to pedestrian traffic – Excellent.

  1 Litre - £25.64      
2.5 Litre - £42.75     
5 Litre - £79.39